To get the latest news about Vigilante Performance's sales and new products, please enter your email address below.

  Home > Stroker Kits by VPE > Chevrolet - 400 Small Block > 400 Cubic Inches - 3.750 Stroke > Dish Top >

A_Villain Engine Kit_Chevrolet 400_6.000 Rod_Dish_-14.8cc_Internal_2 Piece RMS
VPE Villain Engine Kit

Photo may not be actual product

  


Available Part Numbers/Oversize

9015-26622-000 - 4.125
9015-26622-030 - 4.155
9015-26622-040 - 4.165
9015-26622-060 - 4.185


Stroker Kits - Done Right

VPE Villain Engine Kits are available in various displacements and are based on a factory block, 4340 forged steel rods, and a cast steel crankshaft with Probe SRS Series forged pistons. Most feature Nitride Steel Top/Napier Second Ring Sets and are perfectly suited as stock replacement, or they can be set up for high performance street or street and strip combinations. Boost is not recommended with cast steel crankshafts.

The longest rod feasible is utilized in each instance, which gains the maximum piston to counterweight and rod bolt to camshaft clearance possible, as well as decreased piston weight.

Altered stroke and/or compression ratios are not legal for use in emissions controlled vehicles.

VPE - Villain Engine Kit

  • Cast Steel Crankshaft
  • 4340 Forged Steel I-Beam Rods
  • Probe SRS Series Forged Pistons
  • Reduced Tension High-Performance Ring Sets
  • ARP 8740 Cap Screws
  • Balancing is available upon request
  • Components rated at 550+ Horsepower


If you can't find the kit you're looking for please contact us at [email protected] and we'll be happy to assist you in designing a kit that exactly suits your preferences.

Please allow 4 to 6 weeks for piston manufacture

www.P65Warnings.ca.gov



Technical Specs:
Item Code 9015-26622
Vendor NameVPE
Product TypeEngine Kit
Product SeriesVillain
Engine Displacement400
Engine FamilyChevrolet - 400 Based V8
BlockFactory or Aftermarket
Block Height9.008
Base Bore4.125
Piston ManufacturerProbe Industries
Valve ReliefsMost 23d Heads
Piston Material2816-t61
Piston StyleDish
Piston Net Volume-14.8
Compression Height1.125
Pin Diameter.927
Pin Type.150 Wall x 2.500 Long
Pin Material5115 Steel
Ring TypeNitride Steel Top _ Napier Second
Ring Width1.5 1.5 3.0
Gas PortsNo
Gas Port TypeN/A
Crankshaft VendorScat Enterprises
Crankshaft MaterialCast Steel
Crankshaft Stroke3.750
Center CounterweightNo
Reluctor WheelNo
Main Journal2.648
Rod Journal2.100
Rear Main Seal2 Piece
Engine BearingsKing SI Series
BalanceInternal
Rough Bob Weight1,820
BalancedNo
Rod VendorScat Enterprises
Rod TypePro Series I-Beam
Rod Length6.000
Pin EndFloating
Rod Material4340 Forged Steel
Rod BoltARP 8740 Cap Screw
Notes:




Compression Ratio:

 Cylinder Head Volume
Part Number Net cc 58cc 64cc 68cc 76cc
9015-26622-000 -14.8 10.77 10.12 9.73 9.05
9015-26622-030 -14.8 10.91 10.25 9.85 9.16
9015-26622-040 -14.8 10.95 10.29 9.90 9.20
9105-26622-060 -14.8 11.05 10.38 9.98 9.28
Computed with .010 deck and .040 x 4.200 gasket

Browse for more products in the same category as this item:

Stroker Kits by VPE > Chevrolet - 400 Small Block > 400 Cubic Inches - 3.750 Stroke > Dish Top